How to Choose an SMC RB Shock Absorber: RB vs RBL vs RBQ, and How to Calculate Absorbed Energy
2026-11-22When a cylinder’s built-in cushion cannot absorb the end-of-stroke impact, a hydraulic shock absorber is often added. SMC’s RB series is a self-adjusting design: a specially designed orifice absorbs energy across a wide range of speeds and loads without further adjustment. The same family includes the coolant-resistant RBL series and the short-body RBQ series, which allows a 5° eccentric angle and is suitable for absorbing rotation energy. All figures below come from the official SMC English catalogue Shock Absorber RB Series (the ca01.smcworld.com PDF) and, for the series ranges, from the SMC China RB series page. If a document is revised, the current official catalogue prevails.
The short answer
- Calculate the energy to be absorbed, then select the model. Do not order from the thread size alone. Absorbed energy E is kinetic energy E1 plus thrust energy E2. The corresponding mass of the impacting object is Me = 2E / υ². Check Me and collision speed υ against the catalogue graph for that model.
- RB is the standard type, RBL is for atmospheres with non-water-soluble cutting oil, and RBQ is the short type for tight axial space and rotation energy. Thread, stroke and energy ranges are not the same, so the series are not interchangeable by appearance.
- For RB and RBL, the catalogue maximum energy absorption is available only when the full stroke is used. The catalogue also recommends choosing a size with 20% to 40% margin, because absorption capacity falls as the internal working fluid wears or deteriorates.
- A cap (C type on RB, bumper type on RBQ) cannot be fitted later. Order the cap or bumper version from the start. RB0604 is not offered with a cap.
How the three series differ
The ranges for energy, stroke and thread match the SMC China RB series page. Model-by-model figures are taken from the English catalogue specification tables. Maximum energy absorption and maximum operating frequency are measured at room temperature (20 to 25°C).
| Series | What the catalogue highlights | Thread O.D. | Stroke | Max. energy absorption | Collision speed | Ambient temperature |
|---|---|---|---|---|---|---|
| RB (standard; cap type RBC) | Automatic adjustment of absorption performance; the body is strong enough to be positioned without a stopper nut | M6 to M27 | 4 to 25 mm | 0.5 to 147 J | 0.3 to 1.0 m/s for RB0604; 0.05 to 5.0 m/s for the others | −10 to 80°C (no freezing) |
| RBL (coolant resistant; cap type RBLC) | Scraper and rod seal form a double seal; for environments exposed to non-water-soluble cutting oil (mainly JIS Class 1 equivalent) | M10 to M27 | 6 to 25 mm | 3.92 to 147 J | 0.05 to 5 m/s | −10 to 80°C |
| RBQ (short type; bumper type RBQC) | Shortened lengthwise; allowable eccentric angle 5°, suitable for absorbing rotation energy; can also be positioned without a stopper nut | M16 to M32 | 4 to 13 mm | 1.96 to 49 J | 0.05 to 3 m/s | −10 to 80°C |
The RB precautions say not to use the product where cutting oil, water or solvent contacts the piston rod, either directly or as a mist, or where blown dust can collect around the rod, because that can cause malfunction. In a cutting-oil atmosphere, check the RBL “effective atmosphere” line rather than using a standard RB. RBL is specified only for non-water-soluble cutting oil; do not extend that statement to water-soluble coolants or other liquids.
For cylinder seal condition and whether to rebuild or replace the actuator itself, see Seal kit or new cylinder. Compact cylinders can still carry significant inertia at short strokes; see also SMC CQE high-power compact cylinder. Shock absorbers sit with other SMC actuator accessories in the SMC category; use the official catalogue for specifications.
RB standard models
| Basic type | With cap | Thread | Stroke (mm) | Max. energy absorption (J) | Max. operating frequency (cycle/min) | Max. allowable thrust (N) |
|---|---|---|---|---|---|---|
| RB0604 | — | M6 × 0.75 | 4 | 0.5 | 80 | 150 |
| RB0805 | RBC0805 | M8 × 1.0 | 5 | 0.98 | 80 | 245 |
| RB0806 | RBC0806 | M8 × 1.0 | 6 | 2.94 | 80 | 245 |
| RB1006 | RBC1006 | M10 × 1.0 | 6 | 3.92 | 70 | 422 |
| RB1007 | RBC1007 | M10 × 1.0 | 7 | 5.88 | 70 | 422 |
| RB1411 | RBC1411 | M14 × 1.5 | 11 | 14.7 | 45 | 814 |
| RB1412 | RBC1412 | M14 × 1.5 | 12 | 19.6 | 45 | 814 |
| RB2015 | RBC2015 | M20 × 1.5 | 15 | 58.8 | 25 | 1961 |
| RB2725 | RBC2725 | M27 × 1.5 | 25 | 147 | 10 | 2942 |
The order code is RB, then cap type C if required, then the thread/stroke code, then the option code. Example: RBC1412 is the cap type, 14 mm thread O.D., 12 mm stroke. Option codes: blank = two hexagon nuts; J = three hexagon nuts; N = no nuts; S / SJ / SN add one stopper nut to the corresponding nut set. Optional specifications are not available for M6. The catalogue states that a cap cannot be mounted on the basic type; order the cap type from the beginning.
RBL and RBQ model data
RBL matches the same-size RB models for maximum energy absorption, stroke, collision speed, maximum operating frequency and maximum allowable thrust, but it has no M6 or M8 sizes, the spring forces and weights differ, and the effective atmosphere is non-water-soluble cutting oil only. Models are RBL1006, 1007, 1411, 1412, 2015 and 2725; cap types use the RBLC prefix with the same suffix.
| Basic type | With bumper | Thread | Stroke absorption (mm) | Max. energy absorption (J) | Max. operating frequency (cycle/min) | Max. allowable thrust (N) |
|---|---|---|---|---|---|---|
| RBQ1604 | RBQC1604 | M16 × 1.5 | 4 | 1.96 | 60 | 294 |
| RBQ2007 | RBQC2007 | M20 × 1.5 | 7 | 11.8 | 60 | 490 |
| RBQ2508 | RBQC2508 | M25 × 1.5 | 8 | 19.6 | 45 | 686 |
| RBQ3009 | RBQC3009 | M30 × 1.5 | 8.5 | 33.3 | 45 | 981 |
| RBQ3213 | RBQC3213 | M32 × 1.5 | 13 | 49.0 | 30 | 1177 |
On the RBQ specification table, stroke absorption for RBQ3009 is 8.5 mm (the how-to-order page lists that code’s stroke as 9 mm; use the specification table for performance data). A bumper cannot be added to the basic type later.
How the catalogue wants you to calculate energy
The official steps are: identify the type of impact (cylinder stroke at load horizontal / downward / upward, conveyor stroke, free dropping, or rotating impact with torque); list mass m, collision speed υ, bore, operating pressure, thrust, operating cycle and ambient temperature; and confirm that those values fall within the specifications. Then:
- Calculate kinetic energy E1 with the formula for that impact type. For cylinder stroke at load or free horizontal impact, E1 = ½ m υ².
- Select a provisional model and calculate thrust energy E2 from catalogue Data B or Data C.
- Absorbed energy E = E1 + E2, and corresponding mass Me = 2E / υ².
- Check Me and υ on that model’s corresponding-mass graph, and check the operating frequency. Catalogue examples: with m = 1 kg, υ = 0.5 m/s, 10 mm bore and 0.5 MPa, E1 ≈ 0.125 J, E2 ≈ 0.157 J and Me ≈ 2.3 kg, which is below the 3 kg maximum corresponding mass of RB0604, and 30 cycles/min is below that model’s 80 cycles/min. In the other example, m = 50 kg, υ = 0.3 m/s and 40 mm bore give E ≈ 11.7 J and Me ≈ 260 kg, which is below 400 kg for RB2015 at that speed, and 20 cycles/min is below 25 cycles/min.
If the impact energy is smaller than 5% of the model’s maximum energy absorption, select one class smaller. For rotating impacts, also observe the minimum installation radius. Do not use the product in a vacuum or in a pressurised atmosphere that differs substantially from atmospheric pressure, and do not use it in a clean room (the catalogue warns that it could contaminate the room).
Points the catalogue emphasises for installation and maintenance
- RB and RBL need the full stroke to reach the catalogue maximum energy absorption. Speed reduction near the end of the stroke can be large under some conditions; an optional stopper nut can limit the effective stroke.
- Without a cap, surface compression on the contact face is high; that face must be rigid (hardness of HRC35 or more).
- Never turn the screw on the bottom of the body. It is not an adjusting screw, and turning it could cause oil leakage.
- Do not scratch the sliding portion of the piston rod or the outside threads of the outer tube. That can lead to oil leakage, mounting failure or internal deformation.
- Abnormally high impact sounds or vibration, or a large oil leak, means the shock absorber should be replaced; continued use can damage the equipment it is mounted on. If the unit has a cap, inspect the cap for cracks or wear and replace the cap as needed.
- The catalogue’s recommended replacement period, for normal operation at 20 to 25°C, is 1.2 million cycles for RB0604 and RB08, 2 million cycles for RB10 through RB2725, and 1 million cycles for RBL. Replacement may be needed earlier at other temperatures, or when collision speed is near the lower limit (less than 0.1 m/s).
Selection checklist
- Have impact type, mass, collision speed, thrust or cylinder pressure, cycles per minute and ambient temperature all been included, and do they fall within the specifications?
- Is the atmosphere one with non-water-soluble cutting oil? If yes, check RBL. If not, do not apply the RBL atmosphere statement to a standard RB.
- Axial length and eccentric angle: for tight space or mainly rotation energy, look at RBQ (allowable eccentric angle 5°). Do not apply the RB energy table to RBQ.
- If you need a cap or bumper, order that version from the start. RB0604 has no cap type.
- Leave the 20% to 40% energy margin the catalogue recommends, and make sure an RB or RBL unit can use its full stroke.
Ask us to check a combination
Send the type of impact, load mass, collision speed, cylinder bore and pressure (or thrust), cycles per minute, atmosphere and the space you have to mount the unit. We will check it against the official catalogues. Email doskee@dustry.ltd.
FAQ
The cylinder already has a cushion. Do I still need an RB?
The catalogue positions these shock absorbers for absorbing impact and noise, and for deceleration at higher speeds. Whether the cylinder cushion is enough must be checked against that cylinder’s own catalogue (absorbable kinetic energy). If it is not enough, or you need a smoother stop at the end of the stroke, size an external shock absorber with the method above. Do not apply cylinder-cushion figures to the RB energy table.
Can I swap RB and RBL just because the energy ratings match?
Same-size models share maximum energy absorption, stroke and allowable thrust, but RBL has no M6 or M8 sizes, the spring forces and weights differ, and only RBL is specified for a non-water-soluble cutting-oil atmosphere. Recheck atmosphere, envelope and spring force; do not go by the energy figure alone.
Is a stopper nut required?
No. Both RB and RBQ can be positioned directly, without a stopper nut, because of the strength of the body. Use a stopper nut (option codes S, SJ or SN) when you need to adjust stopping time or leave stroke leeway.
Sources: SMC Shock Absorber RB Series English catalogue (PDF, including the RB, RBL and RBQ specification tables, the selection procedure and the product precautions); SMC China web catalogue page “Shock absorber RB” (RB-ZH, series energy, stroke and thread ranges); SMC Chinese catalogue 液压缓冲器 RB系列 CAT.C02-6B (PDF). Model-by-model figures follow the English specification tables. If a document is revised, the current official SMC catalogue prevails.