CKD BNPL Large-Flow Pulse Blow Valve: Port Size, Frequency and Duty
2026-11-19If you want to turn a continuous blow-off line into an intermittent pulse without adding a solenoid valve and a controller, CKD’s BNPL is the large-flow pulse blow valve built for that job. This article uses only CKD’s official product page, the BNPL series catalogue, and user’s manual SM-B25084 (26 October 2026). If the documents are revised, follow the current official PDFs.
The short version
- No separate control equipment: the product page states that simply supplying compressed air generates the pulse; no additional control equipment is required. The manual FAQ also says the valve needs no electrical power — compressed air moves the internal spool and produces the pulse.
- Four port sizes: codes 10 / 15 / 20 / 25 correspond to P and A ports of 3/8, 1/2, 3/4 and 1, with threads in Rc, NPT or G. Effective orifice areas are 75, 90, 175 and 200 mm². Mass is 0.55 kg for 10A/15A and 1.35 kg for 20A/25A.
- Pressure: 0.2 MPa minimum, 0.7 MPa maximum, 1.05 MPa proof pressure. Mounting orientation is universal. Recommended frequency is 2 to 4 Hz (the catalogue notes this recommendation at 0.5 MPa supply pressure).
- The 96% figure is a test reference: the catalogue cover says air consumption can be reduced by 96% versus continuous blow under CKD test conditions, and that 96% applies to the 20A and 25A sizes. It is not a field guarantee.
Size comparison
| Model (size code) | P and A port | Effective orifice area | Mass |
|---|---|---|---|
| BNPL-10 | 3/8 | 75 mm² | 0.55 kg |
| BNPL-15 | 1/2 | 90 mm² | |
| BNPL-20 | 3/4 | 175 mm² | 1.35 kg |
| BNPL-25 | 1 | 200 mm² |
Valve construction is an internal-pilot type with pulse adjustment. The fluid is compressed air. In the model code, A is Rc, N is NPT and G is G thread; the catalogue marks N and G as custom products. Option C adds a protective cover over the adjustment needles to limit accidental changes. The cover can also be ordered separately as BNPL PROTECTIVE COVER 1 (for 10A/15A) or 2 (for 20A/25A).
How to read the model number
The catalogue order code is BNPL + port size + thread + option — for example BNPL-10A (Rc 3/8, no cover) or BNPL-15AC (Rc 1/2, with cover). Confirm the currently orderable codes on CKD’s official model-number page.
- Port size: 10 = 3/8, 15 = 1/2, 20 = 3/4, 25 = 1.
- Thread: A = Rc, N = NPT, G = G thread. N and G are custom products.
- Option: blank = no protective cover, C = with protective cover.
Setting frequency and duty
Two dial needles do the adjustment: C1 sets frequency (cycles per second) and C2 sets the duty ratio (on/off share in one cycle). Needle layout differs between the 10A/15A and 20A/25A bodies, so follow the markings on the valve. After adjustment, push the lock to fix the knobs so a knock does not change the setting.
The manual notes that dial graduations vary from unit to unit, and a fully closed needle does not necessarily read “0”. Do not set frequency or duty outside the catalogue and manual range, or response lag and an unstable pulse can result. Use the frequency/duty characteristic table on catalogue page 5 for reference values; that table was measured on a 15A valve at 0.5 MPa, with secondary piping 15A × 150 mm and a φ5 tip nozzle. Actual frequency still depends on supply pressure, pressure drop, pipe diameter, pipe length and the nozzle, so the manual requires a frequency check before use, with extra caution at 4 Hz or above.
To run continuous blow, the manual says to plug the pilot exhaust port. Remove that plug before returning to pulse blow, or the valve will not operate correctly. With the valve in continuous-blow condition, sealing the blow port can be used to check piping leaks (the manual suggests supplying 0.3 to 0.5 MPa compressed air and applying soapy water).
Catalogue air-consumption example and installation limits
Under catalogue test conditions of 0.5 MPa, 1.3 Hz and a φ8 secondary-side diameter, air consumption per valve is given as 1,800 L/min (ANR) for continuous blow and 72 L/min (ANR) for pulse blow. Like the 96% figure, this is a CKD test reference and should not be applied unchanged to other nozzles or pipe runs. The catalogue also states durability of 100 million cycles or more in CKD’s own tests.
Installation points from the catalogue and manual:
- The valve can be added to an existing steel-pipe continuous-blow line to convert it to a pulse-blow circuit; a straight run makes the retrofit easier.
- Flush both the supply and blow sides thoroughly before connection. Long secondary piping can reduce the air-saving effect and may even prevent a pulse from forming; the manual says to install the valve close to the workpiece, with 1 m as a guideline.
- Do not fit an air gun or a regulator on the outlet. The catalogue states that this raises back pressure on the output port and is not a permitted arrangement.
- Fit a dryer, filter and oil-mist filter upstream to remove moisture and oil. For how compressed-air quality classes are written, see ISO 8573-1 compressed air quality classes.
- The manual warns that the valve is a poppet design using fluorinated grease, so oil or wear particles may be present in the blow air. For higher cleanliness requirements, check the current manual before deciding if the valve is suitable.
Application examples in the manual FAQ include removing dry deposits and assisting workpiece transfer; the same FAQ says moisture or oil may not be blown off, so confirm the actual condition. The catalogue separately mentions intermittent blow after washing automotive parts, and chip removal from machined grooves. Read both together — the catalogue examples are not a claim that water or oil will always be removed.
What to check before you order
- Which of the 3/8, 1/2, 3/4 or 1 port sizes you need, and whether the thread is Rc, NPT or G (the last two are custom products).
- Whether supply pressure stays within 0.2 to 0.7 MPa, whether the valve can sit within about 1 m of the workpiece, and whether the secondary side can stay free of an air gun or regulator.
- Whether the target frequency falls in the recommended 2 to 4 Hz range, and whether you can lock C1 and C2 after measuring the result on the actual piping and nozzle.
- Whether option C or a separate protective cover is needed so the needles are not knocked out of setting.
- Whether the line must stay in pulse mode, or whether some states need the pilot exhaust plugged for continuous blow, as the manual describes.
Ask us to cross-check the official documents
Send the port and thread, supply pressure, secondary pipe length, nozzle details, and the target frequency or duty, and we will check them against the official catalogue and manual: doskee@dustry.ltd.
FAQ
Does BNPL need a power supply or an external controller?
No. The product page says pulse blow is generated from the compressed-air supply alone, with no additional control equipment; the manual FAQ also states that no power supply is required.
Is the 96% air reduction a guaranteed field result?
No. The catalogue marks it as a reference value under CKD test conditions, and the 96% figure applies to the 20A and 25A sizes. The 1,800 L/min versus 72 L/min (ANR) comparison is also limited to the test conditions stated in the catalogue.
How do I switch to continuous blow?
Plug the pilot exhaust port, as the manual describes. Remove the plug before returning to pulse blow. Follow SM-B25084 for the procedure.
Can NPT or G threads be treated as standard catalogue items?
The catalogue lists N (NPT) and G as custom products. Confirm the current orderable range on CKD’s official model-number page before ordering.
Sources: CKD “Large Flow Pulse Blow Valve BNPL” product page (product page); CKD “BNPL Series Catalog” (catalogue PDF); CKD “BNPL Series Large Flow Pulse Blow Valve User’s Manual” SM-B25084 (26 October 2026, Japanese manual PDF); launch notice on CKD product news (26 October 2026). If the documents are revised, follow the current official CKD catalogue and manual.